How to
How to apply a waterproof sticker on a bathroom door
Apply a waterproof vinyl sticker on a dry, prepared bathroom door in 25–35 minutes, with a neat finish around the handle and a gap above the floor.
About 35 min
You will need
- Waterproof door sticker cut to your door size
- Wood putty (only if the door has dents or cracks)
Tools
- Plastic card or squeegee
- Sharp cutter
- Measuring tape
- Dry cloth
- Fine sandpaper
- Hair dryer
1.Check the door is ready
The door must be hard, flat, fully dry and free of loose paint or laminate. If not, follow the preparation steps below first.
2.Clean the surface
Wipe off dust with a dry cloth, then a slightly damp one. Let it dry fully.
3.Line up the top edge
Peel back a few inches of the backing and stick the top edge straight along the top of the door.
4.Smooth downwards
Peel the backing slowly as you go. Press the sticker down with a card from the centre outwards, pushing bubbles to the sides.
5.Trim around the handle and lock
Cut neatly around the handle, lock and hinges with a sharp cutter.
6.Finish above the floor
End the sticker slightly above the floor so mopping water doesn't sit on the bottom edge.
7.Seal the edges
Press all edges firmly. Warm any lifting corner with a hair dryer on low and press it down.
In most Indian homes, the bathroom door is the first door to look old. The lower part takes splashes every day, the laminate or paint starts to lift, and dark patches appear near the floor. Replacing the door is costly and messy. For many doors, a waterproof bathroom door sticker is a quicker fix: it covers the damage and protects the surface from more water.
See our full range of waterproof bathroom door stickers before you read on.
Why bathroom doors get damaged
- Splashes from the shower area hit the lower half of the door daily.
- Mopping water seeps into the bottom edge, which is usually unsealed.
- Steam and humidity loosen paint and laminate glue over time.
- Wet hands leave marks around the handle and lock.
Once water gets under the top layer, the damage spreads faster each monsoon.
When a waterproof sticker is the right fix, and when it isn't
| Door condition | Will a sticker work? |
|---|---|
| Paint or laminate peeling, door still hard and flat | Yes, after you prepare the surface |
| Stains, marks or old paint that looks dull | Yes |
| Small dents or cracks | Yes, after filling them with wood putty |
| Door swollen, soft or crumbling at the bottom | No. Repair or replace the damaged part first |
| Door that no longer closes properly | No. Fix the door first |
A sticker covers and protects a sound door. It does not repair wood that is already soft or rotten.
How to prepare the door (the step most people skip)
- Let it dry fully: keep the door open with the fan on for a day.
- Remove loose layers: peel off lifting laminate or flaking paint.
- Sand smooth: light sanding until the surface feels flat to your hand.
- Fill gaps: use wood putty on dents and cracks; let it dry and sand again.
- Clean and dry: wipe off dust with a dry cloth, then a slightly damp one, and let it dry.
A sticker applied on a clean, flat, dry door lasts far longer than one applied over peeling layers.
How to apply it on a bathroom door
Start at the top, line up the edge, and smooth downwards with a card, pushing bubbles to the sides. Trim neatly around the handle and lock. At the bottom, finish the sticker slightly above the floor so mopping water doesn't sit on the edge. A standard bathroom door takes 25–35 minutes. For more on choosing a look, see our guide to bathroom door sticker designs.
Designs that work on bathroom doors
- Wood grain: looks like a new door and hides small marks.
- Marble and stone: matches tiled bathrooms.
- Plain or textured colour: clean and modern, easy to match with tiles.
- Nature and 3D: a statement door for a guest bathroom.
Browse more styles in our door wallpaper and door stickers collection.
Caring for it
Wipe with a damp cloth. Avoid scrubbing pads and acid cleaners. If an edge lifts after months of heavy splashing, press it down with a little heat from a hair dryer on low.
Why order from Canvas Groove
- Waterproof vinyl, cut to your door size, at ₹99 per sq ft (MRP ₹150).
- Free design proof on WhatsApp before printing. If you don't like it, you get a full refund.
- Free shipping above ₹999, dispatched within 2–3 working days of approving the proof.
All orders are prepaid because every sticker is printed for you; you can cancel within 6 hours of ordering.
Send your door's height, width and a photo on WhatsApp to +91 99585 11990 (Mon–Sat, 10 am–6 pm) for an exact price, or browse all waterproof bathroom door stickers.
Written by
Lovish Taneja is a Director at Canvas Groove. He joined his father Vijay Taneja's printing business in 2020 — a business that has been printing for brands like Fortune, Adani, Emami and Hindustan Unilever since 2000. Lovish learned the printing process on the shop floor in Mayapuri, New Delhi, alongside digital marketing, and now writes Canvas Groove's guides on canvas prints, wallpaper, fridge and door wraps and Vastu décor.
Read more about Canvas Groove or contact the team.
FAQS
Still have questions?
Contact Support